Neptune Tubing

SORT:
VIEW: 32/64
24 items found. Showing items 1 to 24 .
  • 1

    Replacement Tubing for the Neptune DOS Dosing and Fluid Metering System If you need longer tubing for your DOS dosing system or DDR reservoirs. Extend the distance from your pump to the reservoirs, or the pump to your tank.  Two Sizes Available: 4 Meters 16 Meters

    Starting at:
    $4.95

    …at a time!   Large diameter tubing - Larger size tubing means that your pump does not have to work nearly as hard – or stay on for longer cycles. The most popular dosing pumps on the market use tube fittings with the tiny diameter of 1.67mm. The DOS uses much larger tubing and fittings. In fact, at…

    $299.95

    …flow to your RODI.     What's Included? 1x FMM Fluid Monitoring Module 2x Optical Water Level Sensors 1x Float Valve 1x 90° Tube Fitting 1x PMUPv2 1x 4 Meters Orange RO Tubing 1x 3/8" to 1/4" Push Connect Adapter Fitting 1x 1/4" Push Connect Siphon Break 1x Set Screw for Non-Float Valve Applications…

    $199.95

    …objects and also makes it easy to clean and maintain the pump   Easy to connect with standard tubing and fittings The PMUP Has a smooth, 3/8″ (9.5mm) output that will easily connect to silicon tubing or standard push-fit connectors.     Specifications: Dimensions - 4.58" H x 2.24" Diameter Max…

    $49.95

    …The countersunk holes accept almost all major brands of probes, even Neptune's temperature probe.   Dosing Tube Holder The RM30 sump comes standard with four push-connect adapters that can accept any 1/4" OD tubing. They are great for connecting dosing pumps, ATO, and calcium reactor effluent lines.…

    $449.99 $359.99

    …From the box to testing in under 15 minutes! Unlike other testing systems, there are no reagents to mix, tubes to cut, or pumps or probes to calibrate. Simply plug in one cable, two tubes, and run the setup task on the Apex Fusion mobile app — it holds your hand through the installation with helpful…

    $599.95

    …- 2.5 gal (9.3L) Inlet Tubing Size - 0.25" Max Feed Rate - 150 GPH Max Wattage - 70W @ 120VAC   What's Included? 1x CR220 Calcium Reactor 1x VarioS 6 DC Pump 1x Pump Power Supply 1x Pump Controller 2x Push Connect Ball Valves 2x  Suction Cups 1x Inline Check Valve Tubing   What Else Is Required…

    $709.99

    …items that use 1/4" tubing. The solenoid valves uses the 24V accessory port found on 1Link modules and the EnergyBar 832.   Solenoid Valve (SV-1) This 24VDC powered, normally-closed (NC), solenoid valve has push-fit tubing input and outputs designed for standard 1/4″ tubing. The electrical…

    $29.95

    …objects and also makes it easy to clean and maintain the pump   Easy to connect with standard tubing and fittings The PMUP Has a smooth, 3/8″ (9.5mm) output that will easily connect to silicon tubing or standard push-fit connectors.     Specifications: Dimensions - 4.58" H x 2.24" Diameter Max…

    $39.95

    …Holder/Hose Inputs Keep your probes and dosing tubings secure. Hold up to 4 probes in the skimmer section of the sump in the preinstalled probe holder. Each hole is countersunk to keep probes from falling through and one is enlarged to fit a Neptune temperature probe. Installing an included o-ring…

    $564.99

    Know Your Flow! 1/4" Flow Sensor for the Fluid Metering Module from Neptune.  The FS-25 will work with flow rates from 3-12 gph, and will connect to any standard 1/4" push connect tubing. Usually used with a return pump, this flow sensor can be placed in line with the flow on any pipe, connected to…

    $19.95

    …only taking up a minimal amount of space.   CustomCradle XL: Holds up to 4 probes, 4 dosing tubes and 1 top off tube (up to 1/2 inch) Compatible with all temp, pH, conductivity and ORP probes including Neptune Apex Temperature Probe Magnetically mounts to Glass or Acrylic up to 12mm (0.45 inch) The…

    $34.99

    Direct OE replacement fluid metering head assembly for the Neptune DOS Fluid Metering System. The easy to install head replaces the tubing, roller, and plastic housing head cap. Installs in minutes Replaces wearable tubing   The Neptune DOS Replacement Head assembly comes with everything to replace…

    $29.95

    …Push-fit tubing connections   Specifications: Dimensions (approx) - 10.5" x 8.5" x 5.5" Capacity - 2000ml per side (0.52 gallons) Apex, Apex Lite, or Apex Jr. and DOS dosing system required to operate level sensors   What's in the Box? DDR with sensors and cable 4 meters of tubing Getting Started…

    $199.95

    …at a time!   Large diameter tubing - Larger size tubing means that your pump does not have to work nearly as hard – or stay on for longer cycles. The most popular dosing pumps on the market use tube fittings with the tiny diameter of 1.67mm. The DOS uses much larger tubing and fittings. In fact, at…

    $449.95

    …maintain. Thumb screws are a thing of the past with the magnetically coupled, padded probe and dosing tube holder. A single CustomCradle can hold probes, top off tubing, and dosing tubing all in one probe holding device.   Probe holders will organize your probes from a tangled mess to an organized…

    $29.99

    …in direct contact with the heating tube. The Finnex TH series of heating tubes do not come with any type of temperature control. We suggest an external heater controller like the BRS Aquarium Heater Controller, or an aquarium controller such as the Neptune Systems Apex Aquarium Controller. Any…

    Starting at:
    $38.99

    …- 1 gal (3.8L) Inlet Tubing Size - 0.25" Max Feed Rate - 150 GPH Max Wattage - 25W @ 120VAC   What's Included? 1x CR140 Calcium Reactor 1x VarioS 2 DC Pump 1x Pump Power Supply 1x Pump Controller 2x Push Connect Ball Valves 2x  Suction Cups 1x Inline Check Valve Tubing   What Else Is Required…

    $529.99

    …- 2 gal (8L) Inlet Tubing Size - 0.25" Max Feed Rate - 150 GPH Max Wattage - 40W @ 120VAC   What's Included? 1x CR200 CalReact Calcium Reactor 1x VarioS 4 DC Pump 1x Pump Power Supply 1x Pump Controller 2x Push Connect Ball Valves 2x  Suction Cups 1x Inline Check Valve Tubing   What Else Is Required…

    $599.99

    …Holder/Hose Inputs Keep your probes and dosing tubings secure. Hold up to 4 probes in the skimmer section of the sump in the preinstalled probe holder. Each hole is countersunk to keep probes from falling through and one is enlarged to fit a Neptune temperature probe. Installing an included o-ring…

    $359.99

    …Holder/Hose Inputs Keep your probes and dosing tubings secure. Hold up to 4 probes in the skimmer section of the sump in the preinstalled probe holder. Each hole is countersunk to keep probes from falling through and one is enlarged to fit a Neptune temperature probe. Installing an included o-ring…

    $414.99

    …Holder/Hose Inputs Keep your probes and dosing tubings secure. Hold up to 4 probes in the skimmer section of the sump in the preinstalled probe holder. Each hole is countersunk to keep probes from falling through and one is enlarged to fit a Neptune temperature probe. Installing an included o-ring…

    $464.99

    …their skimmate lockers with an air pressure sensitive control box. As the fluid level rises in Davey's Locker it will trap air inside of the sensor tube and pressure will increase, activating the control box. The sensor pickup is very easy to clean and has absolutely no moving parts that can fail. …

    Starting at:
    $174.99

    …their skimmate lockers with an air pressure sensitive control box. As the fluid level rises in Davey's Locker it will trap air inside of the sensor tube and pressure will increase, activating the control box. The sensor pickup is very easy to clean and has absolutely no moving parts that can fail. …

    Starting at:
    $189.99
  • 1