Ro Membrane
- PRODUCTS (93)
- VIDEOS (26)
- INSTRUCTIONS (11)
…GPD membrane has a 99% rejection ratio, and most other membranes cannot make that same claim. Along with meeting NSF/ANSI standards the 75 GPD DOW membrane is hands down the best membrane for our hobby. Up to 99% rejection Dow membrane* - NSF certified Compatible with all 10" RO Membrane Housings.…
…GPD membrane features a 98% rejection rate at 65 PSI which makes it the most commonly used membrane when speed is the primary importance. If you require faster water production and have good water pressure this is one of the better options.BRS generally recommends the use of the 75 GPD DOW membranes…
…for 100 GPD RO Systems -800mL/min What's Included? Dow RO Membrane 2x 2.5" x 2.5" membrane clips 2x 1/8" x ¼" 90-degree elbows 1/8" x ¼" 90° check valve RO membrane housing ¼" tube splitter 5 Feet of Red, White, Blue and Black RO Line DOW Filmtec 75 GPD Membranes have a 96%…
…GPD single membranes or 200 GPD Water Saver System Reverse Osmosis membrane flush/flow restrictor valves increase the flow to the membrane by bypassing the flow restrictor when the valve is opened. This helps flush deposits and significantly increases the usable life of the RO membrane. The Membrane…
…GE, KX Technologies and Pentek. The 10” filter size is the industry standard and will fit our systems as well as virtually every brand of RO system that uses similar looking carbon blocks. Most of the filters included in our kits are made in the USA, NSF Certified or WQA Gold Seal Certified…
…to a properly functioning RO system. Be sure to have the appropriate flow restrictor for the membrane you have. If you decide to change your membrane to a higher or lower GPD membrane, you must also replace the flow restrictor to correspond with the membrane. All BRS Reverse Osmosis Systems…
…GE, KX Technologies and Pentek. The 10” filter size is the industry standard and will fit our systems as well as virtually every brand of RO system that uses similar looking carbon blocks. Most of the filters included in our kits are NSF Certified or WQA Gold Seal Certified and Manufactured…
…RO System. This kit includes: Omnipure Inline Sediment Filter Omnipure Inline Carbon Block We recommend changing sediment filters when they become visually dirty or there is a noticeable drop in pressure. Change carbon blocks every 6-12 months depending on use. This kit does not include a membrane…
These standard RO membrane housings are long-lasting and offer wide membrane compatibility. Membrane housings are relatively standard across the industry, and these housings will fit standard 10" RO membranes, such as the popular Dow Filmtec 75 GPD membranes. Made with high-quality components and…
…takes the following steps Ensure optimal operation of your RO membrane. The higher your membranes rejection rate the fewer TDS your product water will contain resulting in longer lasting resin. The best way to keep the membrane rejection rate up is to monitor and change your prefilters appropriately…
…shut off valves are used with float valves or pressurized tanks to shut off an RO system. It utilizes the back pressure created by the float valve or pressurized tank to shut off the water supply to the membrane. Without an automatic shut off valve waste water would continue to run out after…
This kit works with the BRS 4 Stage Value RO Drinking Water System and is also compatible with most other RO/DI systems that use 10" canisters. Our filter kits feature some of the most widely used and trusted brands in the world Including GE, KX Technologies, Pentek and Omnipure. The 10”…
…which is sold separately. If your RO system has an auto shut off kit or you are planning on installing one the Aquatec PSW Pressure Switches (sold separately) is also required. Benefits of maintaining higher water pressures Improved waste water ratio Improved membrane rejection performance Reduced…
…takes the following steps Ensure optimal operation of your RO membrane. The higher your membranes rejection rate the fewer TDS your product water will contain resulting in longer lasting resin. The best way to keep the membrane rejection rate up is to monitor and change your prefilters appropriately…
…1 Micron Universal Carbon Blocks DualBRS 1 Micron Universal Carbon Blocks Membrane 75 GPD Dow Filmtec Membrane* 100 GPD Dow Filmtec Membrane** Dual 75 GPD Dow Filmtec Membranes* Dual 100 GPD Dow Filmtec Membranes** Deionization Resin Dual Mixed Bed DI Stage with Refillable Cartridge Dual Mixed…
…GE, KX Technologies, and Pentek. The 10” filter size is the industry standard and will fit our systems as well as virtually every brand of RO system that uses similar looking carbon blocks. Most of the filters included in our kits are NSF Certified or WQA Gold Seal Certified and Manufactured…
…with the BRS 4 Stage RO Only System.Our filter kits feature some of the most widely used and trusted brands in the world including GE, KX Technologies and Pentek. The 10” filter size is the industry standard and will fit our systems as well as virtually every brand of RO system that uses…
…takes the following steps Ensure optimal operation of your RO membrane. The higher your membranes rejection rate the fewer TDS your product water will contain resulting in longer lasting resin. The best way to keep the membrane rejection rate up is to monitor and change your prefilters appropriately…
…Black Tubing is commonly used for wastewater lines with reverse osmosis systems and is commonly found coming out of the waste-water fitting on the membrane housing. Six Sizes Available: Each length will be a continuous piece. If you need a single piece longer than what is listed below, check out the…
…550 mL Flow Membrane Flush Valve Reverse Osmosis membrane flush/flow restrictor valves increase the flow to the membrane by bypassing the flow restrictor when the valve is opened. This helps flush deposits and significantly increases the usable life of the RO membrane. The Membrane Flush/Flow…
…three places. We will usually suggest installing the triple TDS meter post source water, post membrane and post DI stage. These three readings will notify you when it's time to change the RO membrane and DI resin. The TRM-1 Triple Inline TDS Meter from HM Digital is one of the most essential reverse…
…10” Long RO Canister Screw - #10-12 x 1"- The long screw is required for the few holes where additional brackets or clips (ex. membrane housing clips) are installed. 20” RO Canister Screw- #14 x 1" - 20” screws are used for attaching 20” RO canisters to a RO bracket. Big Blue…
…and carbon blocks need to be changed. This air filled pressure gauge comes assembled with 1/4" quick connect fittings for quick easy installation in-line before the RO membrane. This product is designed for use with our saltwater aquarium line of RO systems. Pressure Gauge Installation Instructions
…DualBRS 1 Micron Universal Carbon Blocks DualBRS 1 Micron Universal Carbon Blocks Membrane 75 GPD Dow Filmtec Membrane* 100 GPD Dow Filmtec Membrane** Dual 75 GPD Dow Filmtec Membranes* Dual 100 GPD Dow Filmtec Membranes** Deionization Resin Pro Cation DI (Stage 1)Pro Anion DI (Stage 2)Pro Mixed Bed…
…GE, KX Technologies and Pentek. The 10” filter size is the industry standard and will fit our systems as well as virtually every brand of RO system that uses similar looking carbon blocks. Most of the filters included in our kits are made in the USA, NSF Certified or WQA Gold Seal Certified…
…1) Run your RO/DI system for 30 minutes and collect a sample. Sample needs to be water which has passed through the carbon blocks but not the membrane. You can remove the tube coming from the last carbon block to collect the sample or collect a sample from your waste water tube, whichever is easier.…
…you know exactly how the system is performing. BRS suggests: installing the dual TDS meter post membrane and post DI stage. These two readings will notify you when it's time to change the RO membrane and DI resin. This unit features a digital display and comes with two 1/4" GA Murdock Quick Connect…
Membrane housing clips are used to attach the membrane to the RO mounting bracket as well as to attach additional membranes or filters to the original membrane. 2.5" is the standard membrane size. Typically use 2" clips to attach smaller inline carbon filters. Three Options Available 2.5" Membrane…
…will naturally grow faster and are more robust, but Bio-Actif salt is great for fish too by increasing the protection againstdamage to mucous membranes, heightened sensitivity, and elevated mating activity. Free of unwanted Nitrates & Phosphates Contains Bio-Active Marine Substances Includes…
…Technologies, Pentek and Omnipure. The 10” filter size is the industry standard and will fit our systems as well as virtually every brand of RO system that uses similar looking carbon blocks. Most of the filters included in our kits are made in the USA, NSF Certified or WQA Gold Seal Certified…
…Chlorine/VOC Carbon Block Filters with 30% more carbon than standard blocks, GE Purtrex Depth Sediment Filters, American made DOW membranes and Omnipure filters. Dimensions - 16" x 6.25" x 15.5" (RO bracket) / 11.5" diameter x 15" tall (storage tank) BRS 5 Stage Drinking Water RO System Instructions
…RO/DI System Installs and Uninstallsin Seconds No Holes or Drilling Magnetic Mount Dual Optical Eye for Safety Works in Complete Darkness Includes RO Solenoid Valve Eliminates Waste Water Run-Off Optical Sensor Installation The optical sensor can be mounted in any reservoir with a wall thickness…