Ro Water

…the CO2 Scrubber tubing your pumps venturi. Unscrew the body from the head of the reactor and remove the refillable cartridge. Add 1 Tbsp of RODI water to the bottom of the reactor body making sure that it does not touch the CO2 media when the cartridge is replaced. Completely fill the refillable…

…from your membrane, that could harm performance, or even cause a complete clog.   4 Stage Value RO/DI Features: Produce 0 TDS water Minimal waste water Multiple source water connections Mur-lok Push Connect dual EPDM O-Ring fittings 10 Ft Each of 1/4" Blue, Red and Black Tubing Pre-installed NSF…

…your membrane, that could harm performance, or even cause a complete clog.   5 Stage Premium RO/DI Features: Produce 0 TDS water Minimal waste water Multiple source water connections Mur-lok Push Connect dual EPDM O-Ring fittings 10 Ft Each of 1/4" Blue, Red and Black Tubing Pre-installed NSF…

…water for less money. Each BRS 7 Stage Pro Plus system includes multiple accessories from source water connections, pressure gauge, and a triple TDS meter which lets you know the purity of the water the system is producing.    BRS 7 Stage Pro RO/DI Systems are designed to produce ultra-pure water…

…Minimum Water Pressure  50-80 psi 50-80 psi 65-80 psi 65-80 psi Tubing Size 1/4" RO Tubing 1/4" RO Tubing 1/4" RO Tubing 1/4" RO Tubing Water pressure can be increased by adding a booster pump before your RO/DI system. Low pressure may cause the RODI system to produce excessive waste water. Pressure…

…half. The BRS 150 GPD or 200 GPD Water Saver Upgrade Kit will increase the production of any BRS 75 GPD reverse osmosis system to 150 GPD or 100 GPD RO membrane up to 200 GPD without having to use any additional water. With the installation of this kit water production will increase from…

…1 Micron Carbon Block Filter 75 GPD Dow Filmtec Membrane   Parts Bag Includes: 1/4" push connect drain saddle clamp to plumb the waste water line from the RO system to a sink's drain pipe Mur-lok push connect Inline ball valve for easy on/off Filter wrench to tighten and loosen canisters Chrome…

…osmosis unit to supply drinking water on demand.   Kit includes: 3.2 gallon pressurized tank RO tank valve Silver faucet Faucet adaptor Tee for between faucet and pressurized tank Ball valve for turning on and off DI water Check valve for insuring that water in the pressurized tank doesn't flush…

…Depth Sediment Filters, American made DOW membranes and Omnipure filters. Dimensions - 16" x 6.25" x 17.5" (RO bracket) / 6" x 5" x 13" (DI bracket)   Recommended Conditions: Minimum Water Pressure - 50 PSI Max Water Pressure - 90 PSI Recommended Water Temperature - 77°F Recommended Max TDS -

…lifetime of leak free operation. Mur-lok RO fittings are the only reverse osmosis fittings that feature dual EPDM O-rings to ensure a straight leak free fit. These high quality American made fittings are constructed with FDA approved materials. Turns off water flow Polypropylene construction NSF…

…with float valves or pressurized tanks to shut off an RO system. It utilizes the back pressure created by the float valve or pressurized tank to shut off the water supply to the membrane. Without an automatic shut off valve waste water would continue to run out after the float valve is activated…

…found to be the best combination for the most common installations and water conditions. If you have something unique about your water supply or installation please contact customer service and one of our WQA certified water specialists will be able to assist you. Our onsite chat feature is the…

…could harm performance, or even cause a complete clog.   6 Stage Premium RO/DI Features: Produce 0 TDS water Minimal waste water Dual DI Stages Includes Inline Ball Valve Multiple source water connections Mur-lok Push Connect dual EPDM O-Ring fittings 10 Ft Each of 1/4" Blue, Red and Black Tubing…

Why does BRS recommend this? If you find out your water supply is now being treated with chloramines, and you currently have a BRS Value (or most other 4 stage) RODI system and need to upgrade it to a 6 Stage Deluxe RODI system we have put together a kit that is easy to install.  Instead of having…

…found to be the best combination for the most common installations and water conditions. If you have something unique about your water supply or installation please contact customer service and one of our certified water specialists will be able to assist you. Our onsite chat feature is the quickest…

…rejection Dow membrane* - NSF certified Compatible with all 10" RO Membrane Housings. Be sure to change the flow restrictor if you change the flow of your membrane.   FILMTEC reverse osmosis membrane elements for home drinking water are the industry's most reliable. Advanced membrane technology and…

…initial couple minutes of water from your RO membrane will always be high, this is commonly referred to as TDS creep. Diverting the first few minutes of water down the drain can often greatly reduce DI resin consumption. Maintain low levels of carbon dioxide in your water supply. Excess carbon…

Works with all BRS 4 Stage RO/DI Systems This kit is designed to treat all primary water sources that are treated with chlorine and wells with low amounts of contaminants. This kit will work with all BRS 4 Stage RO/DI Systems and most other RO/DI units on the market today that use industry standard…

…found to be the best combination for the most common installations and water conditions. If you have something unique about your water supply or installation please contact customer service and one of our WQA certified water specialists will be able to assist you. Our onsite chat feature is the…

…water pressures. The higher rejection will result in better quality water and lower DI resin consumption. Flow and rejection rates are based on the following: 550ppm soften water 65 PSI 77 degree water 15% Permeate Recovery Data taken after 30 minutes of operation It is very important that the water…

…you require slightly faster water production and have good water pressure this is one of the better options.   TIP -Brand new membranes will have a slight coating on them to help preserve the membrane until it is ready for use.  It is recommended to discard all water that is produced by the new…

Owners Manual  The Tunze RO Water Controller 8555 is used to regulate the water level in your fresh water storage container. It uses two float switches to control an electronic valve. When the water level drops below the first float switch, the valve is opened allowing the container to fill until it…

…Water RO System Instructions   The BRS 5 Stage RO Drinking Water Reverse Osmosis System includes all the essential features necessary to start making pure RO water for your saltwater tank as well as supply drinking water at 75 gallons per day.   Drinking Water Features: 3.2 gallon pressurized water…

…were put through rigorous structural and material testing to help ensure they meet the standards for drinking water. This certification also ensures that Mur-lok tubing can be easily incorporated into any NSF certified drinking water system with minimal paperwork and minimal, if any, re-testing.

…were put through rigorous structural and material testing to help ensure they meet the standards for drinking water. This certification also ensures that our Mur-lok tubing can be easily incorporated into any NSF certified drinking water system with minimal paperwork and minimal, if any, re-testing.

…Source water input: 1/8" MNPT x 1/4" Push Connect Waste water output: 1/8" MNPT x 1/4" Push Connect Product water output: 1/8" MNPT x 1/4" Push Connect Check Valve   Note: Housing has 1/8" Female NPT Fittings. We highly recommend the use of a push connect elbow check valve on the product water line…

…were put through rigorous structural and material testing to help ensure they meet the standards for drinking water. This certification also ensures that our Mur-lok tubing can be easily incorporated into any NSF certified drinking water system with minimal paperwork and minimal, if any, re-testing.

…Push-Connect fittings.    Red RO Tubing is used on most reverse osmosis systems to designate that the water flowing through it is unfiltered. On most reverse osmosis systems the red tubing will run from the source water connection through pre-filters and up to the source water input on the membrane.…

…measurement is the outside diameter of the tubing and will work with all 1/4" Push-Connect fittings.    Blue RO Tubing is commonly used to distinguish filtered water from raw source water. On most reverse osmosis systems the blue tubing will start immediately after the membrane.   Six Sizes…

…were put through rigorous structural and material testing to help ensure they meet the standards for drinking water. This certification also ensures that our Mur-lok tubing can be easily incorporated into any NSF certified drinking water system with minimal paperwork and minimal, if any, re-testing.

…as they need replacement every three years or so, depending on water and set up.   Recommended Installation for this package* Stage One - Omnipure Inline Sediment Filter Stage Two - Omnipure Inline Carbon Block   Our 3 Stage RO Replacement filter kits features the widely used and trusted brand…

…found to be the best combination for the most common installations and water conditions. If you have something unique about your water supply or installation please contact customer service and one of our WQA certified water specialists will be able to assist you. Our onsite chat feature is the…